SOLUTION: A 40-inch length of wire is cut in two. One of the pieces is bent to form a square and the other is bent to form a rectangle three times as long as wide. If the combined area of th
Algebra.Com
Question 798439: A 40-inch length of wire is cut in two. One of the pieces is bent to form a square and the other is bent to form a rectangle three times as long as wide. If the combined area of the square and the rectangle is 55 3/4 inches, where was the wire cut? There are two places where the wire can be cut. One of them is a fraction answer.
Answer by ankor@dixie-net.com(22740) (Show Source): You can put this solution on YOUR website!
A 40-inch length of wire is cut in two.
One of the pieces is bent to form a square and the other is bent to form a rectangle three times as long as wide.
If the combined area of the square and the rectangle is 55 3/4 inches, where was the wire cut?
There are two places where the wire can be cut.
One of them is a fraction answer.
:
Let x = length of the one side of the square
then
x^2 = the area of the square
and
(40-4x) = the perimeter of the rectangle
Let W = the width of the rectangle
then
3W = the length of the rectangle
therefore
2(3W) + 2W = 40 - 4x
Simplify, divide by 2
3W + W = 20 - 2x
4W = 20-2x
Simplify, divide by 2
2W = 10 - x
x = -2W + 10
:
"the combined area of the square and the rectangle is 55 3/4 inches"
x^2 + 3W^2 = 55.75
Replace x with (-2W+10)
(-2w+10)^2 + 3W^2 = 55.75
Foil
4w^2 -40w + 100 + 3w^2 = 55.75
7W^2 - 40w + 100 - 55.75 = 0
7w^2 - 40w + 44.25 = 0
Using the quadratic formula, two solutions
w = 1.5, we will use this one
w = 4.2143
find x
x = -2(1.5) + 10
x = 7 in, the side of square
then
4(7) = 28 inches cut the wire
:
Check this, 40 - 28 = 12 in is perimeter of the rectangle
see if this checks out: w= 1.5, L = 4.5
2(4.5) + 2(1.5) = 12
RELATED QUESTIONS
A 30-inch piece of wire is cut into two pieces, one of which measured x inches. The piece (answered by ankor@dixie-net.com)
A piece of wire 40cm long is to be cut into two pieces. One piece wil be bent to form a... (answered by ankor@dixie-net.com)
A piece of wire 40cm long is to be cut into two pieces. One piece will be bent to form a... (answered by ankor@dixie-net.com)
A 10‐foot piece of wire is cut into two pieces. One piece is bent to form a square. (answered by ankor@dixie-net.com,palanisamy)
A wire 12 inches long is cut into two pieces. One piece is bent to form a square. The... (answered by kev82)
A length of wire is cut into two pieces, one of which is bent to form a circle, the other (answered by josmiceli)
A wire that is 32 cm long is cut into two pieces, and each piece is bent to form a... (answered by richwmiller)
A piece of wire 30com long is cut into two pieces. One of these is bent into a circle and (answered by ankor@dixie-net.com,jsmallt9)
a wire of length 200 cm is cut into two parts and each part of wire is bent to form a... (answered by mananth)