|
Tutors Answer Your Questions about Trigonometry-basics (FREE)
Question 1838: I was given the question to find the angles,
Sin^2 theta = 2cos theta + 2
So I get
1-cos^2 theta = 2cos theta + 2
I think putting this into Ax^2 + Bx +C = 0 would work but is this
Cos^2T + 2CosT +1 = 0
And then plug into quadratic??
Click here to see answer by longjonsilver(2297)  |
Question 2940: Dear Sir,
Please help me in giving the solution to the foll.problem as I am a chemical engineer in doing simulation softwares
Please reply how to determine the value of THETTA in the foll.problem
((THETTA) - SIN(THETTA)) = 0.5268
Regards,
Prem.
Click here to see answer by khwang(438)  |
Question 2993: Dear sir,
Please help me in giving the solution to the foll.problem as I am a chemical engineer in doing simulation softwares
Please reply how to determine the value of THETTA in the foll.problem
THETTA - SIN(THETTA) = 3.4545
I had tried by using Taylor Series but i did't get the correct answer.
Please Solve that Problem and tell me any other simple method is there.
Regards,
Suresh.V
Click here to see answer by longjonsilver(2297)  |
Question 2993: Dear sir,
Please help me in giving the solution to the foll.problem as I am a chemical engineer in doing simulation softwares
Please reply how to determine the value of THETTA in the foll.problem
THETTA - SIN(THETTA) = 3.4545
I had tried by using Taylor Series but i did't get the correct answer.
Please Solve that Problem and tell me any other simple method is there.
Regards,
Suresh.V
Click here to see answer by khwang(438)  |
Question 7102: Can someone tell me if this is correct. Use definitions or identities to find the exact value of the 5 remaining trig functions.
if sin = sqrt(2)/2
then:
sin = sqrt(2)/2
tan = 1
cosecant = 2/sqrt(2)
secant = 2/sqrt(2)
cotangent = 1
They just dont seem correct to me... Thanks for the help
Click here to see answer by Earlsdon(4900)  |
Question 7703: A belt passes over the rim of a flywheel, 20 inches in diameter. What is the linear speed of the belt if it drives the wheel at the rate of 50 revolutions per minute. (The speed of the belt is the same as that of a point on the rim)
Click here to see answer by prince_abubu(198)  |
Question 8198: if given a right triangle with the bottom line length being 8, and the hypotenuse bieng 15 how can i find the top angle (angle x)
x*
l\
l-\
l--\
l---\
l----\
l-----\)))))15 hope the drawing helps :)
l------\
l-------\
l_-------\
l_l____\
))))))8
Click here to see answer by AnlytcPhil(958)  |
Question 18605: I am terrible with algebraic manipulations. I need to solve the following equation for L. I do not want the answer to the question as I have the answer already from the back of the book - I simply need help in rearranging the formula to solve for L. I have the values for P2/P1, and X (I even have the value for L from the solution manual) I know I need to move cos to the other side and I should be solving for cos^-1; however, I am missing some "gene" that does not allow me to figure it out correctly. Any help you can give me would be greatly appreciated.
P2/P1 = cos^2 [(pi*L) / (2X) ]
Click here to see answer by mmm4444bot(95)  |
|
Older solutions: 1..45, 46..90, 91..135, 136..180, 181..225, 226..270, 271..315, 316..360, 361..405, 406..450, 451..495, 496..540, 541..585, 586..630, 631..675, 676..720, 721..765, 766..810, 811..855, 856..900, 901..945, 946..990, 991..1035, 1036..1080, 1081..1125, 1126..1170, 1171..1215, 1216..1260, 1261..1305, 1306..1350, 1351..1395, 1396..1440, 1441..1485, 1486..1530, 1531..1575, 1576..1620, 1621..1665, 1666..1710, 1711..1755, 1756..1800, 1801..1845, 1846..1890, 1891..1935, 1936..1980, 1981..2025, 2026..2070, 2071..2115, 2116..2160, 2161..2205, 2206..2250, 2251..2295, 2296..2340, 2341..2385, 2386..2430, 2431..2475, 2476..2520, 2521..2565, 2566..2610, 2611..2655, 2656..2700, 2701..2745, 2746..2790
|
| |